How to: Conduct a Wireless Site Survey ?? ?With wireless systems, it’s very difficult to predict the propagation of radio waves and detect the presence of interfering signals without the use of test equipment. Even if the system implements omni-directional antennas, radio waves?don't?really travel the same distance in all directions. Instead walls, doors, elevator shafts, people, and other obstacles offer varying degrees of attenuation, causing the RF (radio frequency) radiation pattern to be irregular and unpredictable. As a result, it’s absolutely necessary to perform a wireless site survey to fully understand the behavior of radio waves within the operating environment before installing access points.Site survey conceptsThe ultimate goal of a wireless site survey is to determine the number and placement of access points (or mesh nodes) that provides adequate signal coverage throughout a facility or city area. With most implementations, “adequate coverage” means support of a minimum data rate or throughput. In order to perform a successful survey,?you'll?need to relate the required performance to a value that survey tools measure, such as?SNR. A wireless site survey also detects the presence of?RF interference?coming from other sources that could degrade the performance of the wireless LAN.
When conducting a wireless site survey, consider the following steps and tips:? ?1. Understand the wireless requirements -?In order to identify optimum locations for access points or mesh nodes, you must have a good understanding of specific requirements for the network that impacts signal coverage. For example, maximum range between a client device and the access point decreases as data rate and resulting performance increases. Thus, you need to know the target data rates (and throughput) to correctly interpret survey results. Also, client devices may have relatively low transmit power, which must be taken into consideration when using most site survey tools.
? ?2. Obtain a facility diagram -?
Before getting too far with the site survey, locate a set of building blueprints or city maps. If none are available, prepare a drawing that depicts the location of walls, walkways, etc. Site survey?tools?import diagrams in various image formats. Of course mapping software is a good source for outdoor city surveys. If all else fails for in-building surveys, consider taking a digital photograph of the fire escape diagram, which is usually present on hallway walls.
???3. Visually inspect the facility -?
Walk through the facility before performing any testing to verify the accuracy of the facility diagram. This is a good time to note any potential?attenuation barriers?that may affect the propagation of RF signals. For example, a visual inspection will uncover obstacles to signals such as metal racks and partitions, items that blueprints generally don’t show. Also, note possible locations for mounting access points, such as above ceiling tiles or on pillars. For outdoor city environments, you should carefully assess the locations and availability of street lights and water towers for mounting mesh nodes and backhaul equipment. These actions will make the later testing efforts go much more smoothly.
? ?4. Assess existing network infrastructure -?
Determine the capacity of any existing wired networks that can interface the access points or mesh nodes. Most buildings have Ethernet and in some cases optical fiber networks. Check on how much of the existing networks can be made available for supporting the wireless network. This will aid designers later on in the deployment when defining the architecture and bill of materials for the wireless network.
???5. Identify coverage areas -?
On the facility diagram or city map, indicate all areas where coverage is needed, such as offices, hallways, stairwells, utility rooms, bathrooms, break rooms, patios, parking garages, and elevators. Also, identifying where users will not wireless coverage is important to avoid wasting time surveying unnecessary areas. Keep in mind that you might get by with fewer access points and lower equipment costs if you can limit the roaming areas.
???6. Determine preliminary access point locations -?
By considering the location of wireless users and range estimations of the wireless LAN products?you're?using, approximate the locations of access points that will provide adequate coverage throughout the user areas. Plan for some?propagation overlap?(generally 25 percent) among adjacent access points, but bear in mind that channel assignments for access points will need to be far enough apart to avoid inter-access point interference.
Be certain to consider mounting locations, which could be vertical posts or metal supports above ceiling tiles. Recognize suitable locations for installing the access point, antenna, and data /?PoE?cable. Also think about different?antennas?when deciding where to position access points. An access point mounted near an outside wall, for example, could be a good location if you use a patch antenna with relatively high gain oriented within the facility.?
???7. Verify access point locations -??
This is when the site survey testing begins. Most wireless LAN vendors provide wireless site survey software that identifies the associated access point, data rate, signal strength, and signal quality. You can load this software on a laptop and test the coverage of each preliminary access point location. Alternately, you can use a third party site survey tool available from several different companies, such as?AirMagnet,?Berkeley Varitronics Systems, and?Ekahau.
Install an access point at each preliminary location, and monitor the site survey tool readings by walking varying distances away from the access point. There’s no need to connect the access point to the distribution system because the survey tests merely ping the access point or read the beacon signal strength. Very important: Definitely consider the?SNR range boundary?and?uplink signal strength?when interpreting the results. To make the access point easy to move about the facility, you can mount it on a pole attached to a cart with a battery and DC/AC converter. Otherwise,?you'll?need to haul around an extension cord and always be looking for where to plug in for power (not recommended).
Take note of performance or signal readings at different points as you move to the outer bounds of the access point coverage. In a multi-floor facility, perform tests on the floor above and below the access point. Keep in mind that a poor signal quality reading could indicate that RF interference is affecting the wireless LAN. This would warrant the use of a spectrum analyzer to characterize the interference, especially if there are no other indications of its source. Based on the results of the testing, you might need to reconsider the location of some access points and redo testing for the affected locations. ? ?8.?Document findings -?Once?you're?satisfied that the location of access points?you've?identified will provide adequate signal coverage, document your findings on the facility diagrams by depicting the location of each access point. The installers will need this information.
These steps will point you in the right direction, but experience really pays off. If?you're?new to wireless LANs,?you'll?begin to build an odd intuition about the propagation of radio waves after accomplishing several wireless site surveys.
AirMagnet Survey -?Wireless Network & Access Point Installers in Carson, CA
Design and deploy wireless LANs for optimal performance, security and compliance
- 802.11a/b/g/n and 4.9 GHz site surveying of indoor and outdoor networks
- “Real-world” measurements provide accurate deployment guidance
- 802.11n, voice & spectrum surveys
- Customized reporting to save time and deliver reports based on project requirements
- Seamless integration with AirMagnet Planner
AirMagnet Survey is the industry's most accurate solution for planning and designing 802.11 a/b/g/n wireless LANs for optimal performance, security and compliance. It calculates the ideal quantity, placement and configuration of APs for a successful WLAN deployment.
AirMagnet Survey goes beyond just verifying RF coverage, by plotting actual end-user network performance in terms of connection speed, throughput and packet statistics. The end result is a complete Wi-Fi “weather map” of all critical RF and end-user performance metrics.
Advanced features allow users to integrate with professional spectrum analyzers, model pre-deployment scenarios, generate customized survey reports, perform outdoor surveys, conduct voice surveys, verify end-user network requirements, and do detailed end-user capacity planning.
AirMagnet Survey is available in “Express” and “PRO” versions. AirMagnet Survey Express offers a lighter version of the solution that allows users to perform the basics of Wi-Fi site surveying with ability to map out signal, noise and even user performance. AirMagnet Survey PRO extends those capabilities found in the Express version and adds powerful, industry-defining features including 802.11n deployments, multi-floor deployments, outdoor surveys, network design verification, voice readiness verification and surveys, RF spectrum analysis, and many more. ?Read more about our? Wireless?AirMagnet Survey?here.
|
? |
|
|
